Introduction to woodworking band saw machine operating skills:

1. It is called a carpenter who has a dedicated person to operate it. For machine tools, the operator must pass the examination and hold the "Equipment Operation Certificate" of the machine tool to operate it; for carpentry machine tools that do not have a fixed person to operate, the operator should also hold the "Equipment Operation Certificate" of the machine tool. Use machine tools.

2. Carefully implement the following general rules for carpentry machine tools:

(1) Carefully do the following after operation:

1. Fix For machine tools that are operated by dedicated personnel, the operator should carefully read the shift handover records to know the operating conditions and questions of the previous shift of machine tools.

2. Check the machine tool and the work site. If there are any debris that is not related to the work, remove them.

3. Check that the safety protection equipment should be in complete condition. Machine tools without protective equipment are prohibited from operation.

1. The viewing operation should be in a non-working position.

2. Check that the electrical distribution box should be closed securely and have good electrical grounding.

3. Check that the amount of oil in the lubricating oil storage area is sufficient and the sealing is good. The oil mark, oil cup, oil nozzle, etc. should be complete and installed correctly, and the oil eye should not be blocked. Oil according to smooth chart rules.

(2) Do the following carefully during operation:

1. For machine tools that are fixed to be operated by dedicated personnel, operators should stick to their posts, operate carefully, and never do anything inappropriate. Things that have nothing to do with homework. Stop the machine and cut off the power supply when leaving the machine. If a machine tool is not operated by a dedicated person, the operator should stop the machine and cut off the power supply after taking possession of the machine tool.

2. Tools and wood should be clamped correctly and fastened reliably.

3. The mechanical speed change of transmission and feed must be stopped after the tool separates from the workpiece.

4. Pay attention to the fact that there should be no iron nails on the wood to prevent damage to the knives.

2. When an accident occurs with a machine tool, the machine should stop immediately, keep the scene of the accident, and report to the relevant departments for analysis and handling.

(3) After work, do the following carefully:

1. Place the operating handle in the non-working position and cut off the power supply.

2. Clean the machine tool and clean the working area.

3. Carefully implement the following special rules for carpentry machine tools:

(1) Carpenter lathe:

Tools should be installed on removable Turn on the adjusted tool holder or hold it tightly against the tool holder. Do not turn while hanging in the air.

(2) Carpenter milling machine:

1. When working, wait until the spindle is operating normally before dry milling. When using a large-diameter milling cutter, you should start milling at slow speed. .

4. ФM carpenter milling machine is only allowed to use the cutter head at the speed of 1320 rpm. The other three powers of 2010, 2645 and 4080

are prohibited from using the cutter head. Perform milling.

(3) Carpenter planer:

1. Use manual turning before work, and start the machine tool after confirming that the tool changes flexibly.

2. Material can be planed after the machine tool starts working normally.

3. Planing: (1) The protective board should be moved according to the width of the wood.

(2) When planing, pay attention to check whether the knots on the wood are dead or alive to avoid hurting people.

4. Pressing and planing: When planing, pay attention to the big head and small tail of the wood, and give appropriate effort according to the size of the wood. The maximum size should not exceed 5 cm.

(4) Carpenter sawing machine:

1. Circular saw machine:

(1) After operation, check whether the circular saw blade should be installed Correct, fastening and reliable. The use of manual turning should be flexible.

(2) The feeding amount should not be too large when sawing. If the saw blade power slows down due to excessive feeding, the wood should be slightly moved back immediately until the rotation speed recovers. Feed again.

(2) When adjusting the inclination of the workbench as needed, be careful not to touch the saw blade and clips, and level the workbench in time after the operation is completed.

(3) The feeding amount should not be too large when sawing. If the saw blade power slows down due to excessive feeding, the wood should be slightly moved back immediately, and the saw blade should be retracted after the rotation speed recovers. Feeding. (4) After operation, lower the upper flywheel to relax the saw blade.

3, 48"Sports band saw machine:

(1) After operation:

① Adjust the saw blade Make it tight and appropriate, and the tooth top is 20 mm higher than the edge end of the flywheel.

② There are hardwood blocks on the upper and lower rolling heads to clamp the saw blade so that it will not swing, but it must not be clamped so tightly that the saw blade will heat up.

③ Close the wooden protective cover door of the upper flywheel.

② Always rub some kerosene or water on the saw blade to make it smooth and cool.

③ The upper rolling head slider should be moved to a distance of 50~100 mm between the upper rolling head and the wood being sawed.

④ The speed of the sports car should be determined according to the size and softness of the wood being sawn.

⑤ When cutting round wood into square material, you only need to tie up the fishing line. When sawing round wood into thin pieces, it is necessary to tie up the upper and lower fishing lines together.

⑦ When a problem occurs while the wood is being sawed and the sports car wants to return, the joystick installed on the sports car frame to prevent the movement of the wooden frame should be grasped to prevent the wooden frame from moving.

⑧ It is forbidden to add lubricating oil or tighten bolts while the machine tool is in motion.

⑨ When the machine tool is out of use or the sports car is loading, the sports car joystick controller should be controlled.

(3) After operation, lower the upper flywheel to relax the saw blade.